1
How to Configure the TCP/IP Network Protocol Windows 2000:1. Click on Start-> Settings-> Network and Dial-up Connections.2. Choose Local Area Co
3. Click on Internet Protocol (TCP/IP) and then click on Properties.4. Click on Use the following IP address. Make sure you set the Subnet mask to 25
How to Configure the TCP/IP Network Protocol Windows XP:1. If you are in classic Start menu view, click on Start->Settings->Control Panel->Ne
4. Key in the IP Address that you chose earlier. The subnet mask is entered automatically in Windows XP. Click OK.Now the configuration of your PC’s
If you already have an established local area network, the following steps will allow you to determine the three common segments that the IP addresses
b b. Click on View NetworkConnections. c c. In the Network Connectionswindow, you should see an icontitled Local Area Connection (orsomething simila
d. A window with the title LocalArea Connection Status (orsomething similar) will appear.Click on the Support tab. Underthe heading Address Type, you
How to Connect Your Hard Drive to the Network Storage Center:1. Loosen the two screws on the rear panel either using a screwdriver or by hand. Screws2
5. Push the power connector into the power socket of the hard drive, as shown. The power cable is designed to go in one way, to avoid any potential er
If you are using the Network Storage Center for the first time, the Setup Wizard will provide you with a simple and easy way to set up the device. The
Trademarks & CopyrightWindows 95/98/ME and Windows NT/2000/XP are registered trademarks of Microsoft Corp. All other brands and product names are
2: Follow the Setup Wizard to Complete Installation Power On Connect the power cord and press the “Power” button on the front panel of the Network Sto
LAN Connection Connect the Network Storage Center and router/switch (or PC) with an RJ-45 Ethernet cable. Ensure that the “Link/Act” LED is lit gr
3: Click “Next” to start the Scan Prepare to Scan Scan Hard Drives on the Network The Setup Wizard will scan your network to locate all available Ne
Refer to the figure on the following page. Select the Device you want to set up and Click “Next”. Reachable Status ActionNO The Network HD’snetwork
User name/Password Reminder When the box shown above appears, please input “admin” in both fields, as these are the default values for both the User N
The Setup Wizard should complete successfully. This will be indicated by the red check marks in the figure on the previous page.If the Setup Wiza
Click OK to set up your Network Storage CenterClick OK to access the device’s web-based user interface, or click Cancel to close the Setup Wizard prog
1. Click the “Access my Network HD” icon to access the Network Storage Center. There are three pre-defined accounts for you to use: all, power, guest.
Set Up the Network Storage Center In order to configure the Network Storage Center via your computer using a web browser, please follow the steps list
HomepageThe Network Storage Center has a web-based graphical user interface (GUI) that can be accessed using a standard HTML (HTTP v1.0) compliant bro
Introduction 4Package Contents 5 Hardware Description 6 IP Protocol Setup 7 Hard Drive Installation 17 Quic
Status Details To see more info about the Network Storage Center, such as percent of hard drive used, “up-time”, Sambausers, and FTP users, please cli
Network Settings In the Network Settings page, you can set up or change the networking configurations for the device, including Host Name, IP Address
IP Address Item ConfigurationIP Address The Network Storage Center’s IP Address Subnet Mask The Subnet Mask must be compatible with the other device
Superuser/PasswordIn this page, you can set up the administrator’s User Account/Password. You will need this to access the web-based UI to set up and
AdministrationOn this page, you can manage the Network Storage Center using the following tools: System Restart HD FormatFactory Default R
HD Format When you see this message “HD Unable to use” in the “(%) of HD used” field (see figure below), it means that your hard drive is a new, unfor
Factory Default Reset To restore the Network Storage Center to its default configuration, click “Yes” (see figure below). Do not power off the device
System Time 1. If your system is not connected to the Internet, click “Time Sync” to synchronize the current time with your PC’s. 2. If your system is
ShareFrom this section, you can manage the Network Storage Center’s users and folders. User configuration On this page, you can add and remove users,
1. Click the Add button. 2. Enter the appropriate information for: User Name, New Password, Confirm Password, and User Description3. Decide on the FTP
Powerful and EasyThe compact Hawking HNAS1 Net-StorTM Network Storage Center is an economical and powerful device, and provides an ideal solution for
Delete User To remove the user’s account to stop the right of using the Network HD, 1. Select the User you want to remove by clicking the check box ne
Folder Configuration In this section, you can add and delete folders, as well as set up the authentication of users. Add Folder To add a new folder fo
Delete Folder To remove a folder and files inside 1. Select the folder you want to remove by clicking on the check box next to the folder’s name.2. Cl
Change the User Authentication for a Folder Every user has a certain type of access privilege to use the Network Storage Center. This access privileg
FTPFor remote access or backup, you can utilize FTP Client software to use the Network Storage Center. FTP Configuration To change configurations such
FTP Password In this section, you can set up the FTP account password. The Default User name is “ftpuser”, and the default password is “abc123”. Ple
It is recommended (but not necessary) that you map the Network Storage Center to your PC as a network drive. Thedevice will then automatically reconne
2. A new window will appear and will ask you to specify a drive letter for connection, and the folder that you would like to connect to. An example i
4. An icon similar to the one indicated by the red arrow in the figure below will appear. You will now always be able to access the drive from “My Co
There are several applications for the Network Storage Center. Individual users can back up important files from their PCs. PCBackup Data Individual U
Unpack and Inspect Open the package and carefully remove all items. The complete HNAS1 package consists of: x One HNAS1 Network Storage Center (hard
4. Select “Back up My Computer” to back up your wholesystem or “Back up Selected files, folders and Driver”. Ifyou want to backup “C:\”, select “Back
1. How do I shut down the Network Storage Center properly?Ans. To shut down the system properly, hold the Power button on the front of the unit down f
5. I use my Network Storage Center as an FTP server, but the users outside the local area network (LAN) cannot access it. Ans. To use the Network Stor
StandardsIEEE 802.3, IEEE 802.3u Supported Protocols TCP/IP, HTTP, SMB, FTP Number of Concurrently Supported Users Samba: Five Users; FTP: Five Users
Front Panel Power Button To activate the Network Storage Center, press this Power button located onthe front panel of the device. To power off the uni
Configuring the Network Protocols Please Note: If your PC obtains its IP address automatically, the Setup Wizard will not be able to get the PC’s IP i
How to Configure the TCP/IP Network Protocol Windows 98/Me:1. Click on Start-> Settings-> Control Panel-> Network.2. Click TCP/IP -> Ether
3. Click IP Address and click on Specify IP Address.4. Type in the IP Address. Make sure you set the Subnet Mask to 255.255.255.0.5. Click OK. At thi
Commenti su questo manuale